Getting Familiar with Plumbing: A Must for Installing a Bathtub
Getting Familiar with Plumbing: A Must for Installing a Bathtub
Blog Article
This great article following next about Installing A Bathtub is seriously stimulating. Read it for your own benefit and figure out what you think about it.
Mounting a bathtub isn't precisely rocket science, however it does call for solid plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old tub with a new one is additionally a reasonably tough project. If the old bathtub is easily obtainable, the job can relocate quickly; if you need to open up a wall to eliminate the old bathtub and place the new tub, the job is a lot harder. In either case, the task is within a home handyman's skills, although you will certainly need a helper to vacate the old tub as well as embeded in the brand-new one. Make sure you have certified on your own for the task and also fit trying it. Rather than hiring a specialist to take control of a halfway-completed task, it is much better to take into consideration using one prior to you start. Opportunities are you may need a professional plumber to make tube connections.
This write-up will aid you install a brand-new bathtub in your bathroom if you have currently acquired a brand-new tub and also do not require to alter the setup of your previous water system pipes.
Your devices and also product checklist must consist of the following:
Preparing for the Installment
First of all, the supporting structure provided with the bath ought to be fitted (if required) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is essential to make certain that if the tap includes a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the faucets unit to prevent stress on the bathtub.
Fit the flexible tap ports to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its final placement.
Removing Old Taps
If you need to change old taps with new ones as a part of your setup, after that the first thing you need to do is separate the supply of water. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The process of removing the existing taps can be quite problematic due to the limited gain access to that is commonly the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the faucets. Have a cloth ready for the staying water that will certainly originate from the pipes. Once the supply pipelines have actually been gotten rid of, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary taps from transforming during this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing compound.
Before moving on to fit the new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new taps to fit.
Mounting the Bathtub
Making use of the two wood boards under its feet, put the bathtub in the needed setting. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four small factors.
The following objective is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level and also adjusting the feet on the bathtub till the level checks out level.
To install faucets, fit all-time low of the outermost versatile tap adapter to the proper supply pipeline by making a compression join; then do the very same for the other faucet.
Switch on the water and check all joints and brand-new pipework for leaks and tighten them if essential. Load the tub as well as likewise check the overflow outlet and also the normal outlet for leaks.
Lastly, fix the bath paneling as described in the supplier's user's manual. Tiling and sealing around the bath tub ought to wait until the tub has actually been used at least once as this will certainly settle it into its final setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, then you will need lowering couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, place the faucet in the installing opening in the bath/basin making certain that the washers are in place between the faucet as well as the sink. Secure the faucet in position with the manufacturer provided backnut. As soon as the tap is firmly in place, the supply pipes can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular tap adapters. The previous kind ought to be attached to the tap finishes first, tightening just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to split a rigid seal, creating the water to penetrate the wall surface in between the bathroom as well as the tiling, causing difficulties with dampness as well as possible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and fittings. They are sold in tubes and cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water prior to securing, to permit the activity experienced when the bathtub is in use. The sealer can split relatively early if you do not take into account this movement prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also quickly readily available on the market. It is recommended to fit the floor tiles making use of waterproof or water resistant adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I found that entry about How to Install a Bathtub Yourself when doing a search on the search engines. Are you aware of someone else who is fascinated about the topic? Please feel free to promote it. Thanks a lot for your time spent reading it.
About Report this page